| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: Fix pcl_for_each_segment for empty chunks
When a parsed chunk list contains a chunk whose ch_segcount is zero,
pcl_for_each_segment computes its inclusive upper bound as
&chunk->ch_segments[ch_segcount - 1]. ch_segcount is u32, so the
subtraction wraps to 0xFFFFFFFF and the bound lands far past the
ch_segments flex array. The loop body then walks unrelated memory at
sizeof(struct svc_rdma_segment) stride until it faults.
A zero-segcount chunk is reachable from the wire:
xdr_check_write_chunk() only rejects segcount values greater than
rc_maxpages, and pcl_alloc_write() links a freshly allocated chunk
onto rc_write_pcl/rc_reply_pcl before its segment-fill loop runs,
so a Write or Reply chunk advertising zero segments leaves
ch_segcount == 0 on the list. When the transport has negotiated
Send-With-Invalidate, svc_rdma_get_inv_rkey() iterates all four
PCLs with pcl_for_each_segment and dereferences segment->rs_handle
on each iteration, turning the underflow into an out-of-bounds read
and a general protection fault.
xdr_check_write_list / xdr_check_reply_chunk
pcl_alloc_write()
chunk = pcl_alloc_chunk(...) /* ch_segcount = 0 */
list_add_tail(&chunk->ch_list, &pcl->cl_chunks)
/* fill loop iterates zero times for wire segcount 0 */
svc_rdma_get_inv_rkey()
pcl_for_each_chunk(rc_write_pcl)
pcl_for_each_segment(segment, chunk)
pos <= &ch_segments[0u - 1u] /* 0xFFFFFFFF */
segment->rs_handle /* OOB read -> GPF */
Fix by switching the macro to a half-open upper bound that uses
ch_segcount directly. For ch_segcount == 0 the loop start equals the
loop end and the body is skipped; for ch_segcount > 0 the iteration
range is unchanged. All six existing call sites in
net/sunrpc/xprtrdma/svc_rdma_recvfrom.c and
net/sunrpc/xprtrdma/svc_rdma_rw.c remain correct under the new bound,
so no caller changes are needed. |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: Reject inline replies that overflow the pull-up buffer
An RPC-over-RDMA client can request a reply, such as an NFS READ
payload, without providing a Write list or a Reply chunk to carry
it. When such a reply needs more scatter/gather entries than the
device's Send Queue supports, svc_rdma_pull_up_needed() selects
pull-up and svc_rdma_pull_up_reply_msg() linearizes the whole
reply into sctxt->sc_xprt_buf. That buffer is only sc_max_req_size
bytes, while the reply on this path is bounded only by the client's
request, so svc_rdma_xb_linearize() copies past the end of the
buffer and corrupts adjacent slab memory. The oversized length is
then stored in sc_sges[0].length and posted, so the device also
reads beyond the mapped region.
The SGE-exhaustion branch is the only pull-up path that can exceed
the buffer: the threshold branch pulls up only replies smaller
than RPCRDMA_PULLUP_THRESH, and replies that fit the device's SGE
budget are sent directly without linearization. Make
svc_rdma_pull_up_needed() report -E2BIG when the reply it would
pull up cannot fit sc_max_req_size, and fail the request with
ERR_CHUNK as RFC 8166 Section 4.5.3 directs rather than dropping
the connection.
The helper no longer answers a simple yes/no question: it now
reports pull-up, no pull-up, or -E2BIG for a reply too large to
linearize. Rename svc_rdma_pull_up_needed() to
svc_rdma_check_pull_up() so its name no longer implies a boolean
predicate. |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: Reject Read lists that exceed the page budget
Individual Read segment lengths are validated at decode time, but
nothing prevents a requester from sending multiple segments whose
cumulative length exceeds the rq_pages array budget. When one
segment fills the page array exactly, the runtime guard in
svc_rdma_build_read_segment() is bypassed because len reaches zero.
A subsequent segment then accesses the NULL sentinel slot at
rq_pages[rq_maxpages], resulting in a NULL pointer dereference during
DMA mapping.
Accumulate pages across all Read segments and reject the message at
decode time when the total would overflow the page budget. |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: Validate Read chunk positions before reconstruction
The RPC/RDMA Read chunk position field is supplied by the remote
client and stored verbatim in the parsed chunk list.
xdr_count_read_segments() checks only 4-byte alignment; it never
compares the position against the received inline body length.
In the single-chunk path, svc_rdma_read_complete_one() splits the
head and tail kvecs at ch_position. A position past the inline
body underflows the tail length, exposing adjacent slab memory to
the upper XDR decoder.
In the multi-chunk path, svc_rdma_read_multiple_chunks() computes
gap lengths between chunks as unsigned subtractions from
ch_position. Overlapping Read chunks cause these subtractions to
underflow. A final position past the inline body likewise
underflows the trailing gap length. svc_rdma_copy_inline_range()
then copies past the receive buffer into request pages that are
returned to the client through the Reply channel.
Bound inline-range copies in svc_rdma_copy_inline_range() against
the decoded inline RPC body saved in rc_saved_arg. Reject a
single Read chunk positioned beyond that body, and reject
multi-chunk lists where accumulated read bytes exceed the next
chunk's position. Apply the same position and overlap checks in
the call-chunk interleaving path. |
| In the Linux kernel, the following vulnerability has been resolved:
qede: Fix NULL pointer dereference in TPA fragment processing
Under memory pressure, the qede driver encounters NULL pointer
dereferences when processing TPA continuation fragments.
Commit 8a8633978b84 ("qede: Add build_skb() support.") accidentally
dropped the assignment of tpa_info->buffer.data in qede_tpa_start().
When memory pressure causes an SKB allocation failure in qede_tpa_start(),
the driver sets tpa_start_fail = true and attempts to recycle the physical
page later in qede_tpa_end() via qede_reuse_page(). However, because
buffer.data was left uninitialized (NULL), qede_reuse_page() pushes a
"ghost" BD (valid DMA mapping but NULL data pointer) back into the
active Rx ring.
The next time the hardware uses this ring slot, it passes a NULL page
to qede_fill_frag_skb(), causing a kernel panic.
Example crash from production system:
BUG: unable to handle kernel NULL pointer dereference at 0x8
RIP: qede_fill_frag_skb+0x96/0x430 [qede]
Call Trace:
qede_rx_int+0xb06/0x1de0
qede_poll+0x2f4/0x6c0
__napi_poll+0x2d/0x130
Fix the root cause by restoring the tpa_info->buffer.data assignment
in qede_tpa_start(), ensuring valid pages are correctly tracked and
recycled. Additionally, update the stale comment for
struct qede_agg_info::buffer to reflect its current usage. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/cxgb4: Cancel reg_work before freeing device on remove
c4iw_uld_state_change() queues reg_work to register the RDMA device.
c4iw_remove() can free ctx->dev while this work is pending or running,
leaving c4iw_register_device() accessing the freed device.
Cancel reg_work before removing the device. The registration work can
tear down ctx->dev when registration fails, so do not unregister or
deallocate it again in that case.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: Fix CT limit teardown use-after-free
Packet processing uses CT limit state under RCU, while netns teardown
frees that state under ovs_mutex. The CT limit pointer was neither removed
from readers nor protected by a grace period, allowing packet processing to
dereference the freed state.
An unprivileged user can trigger this bug from a user and network
namespace, causing a slab-use-after-free in ovs_ct_execute() when the
netns is torn down.
Publish the CT limit pointer through RCU, remove it before teardown, and
wait for readers before freeing its contents. Keep ovs_mutex around
individual CT limit updates, and use the RCU read-side lock while GET
traverses the RCU-protected limit lists.
Netns teardown detaches the RCU-protected CT limit state in the pernet
.pre_exit callback while holding ovs_mutex. The pernet core guarantees an
RCU grace period between the .pre_exit and .exit callbacks, so the .exit
callback completes the teardown without adding any extra synchronization.
The netlink command handlers do not need NULL checks because the userspace
netlink socket holds an active reference to its network namespace while a
request is processed. The per-netns exit path therefore cannot run
concurrently with SET, DEL, or GET for that socket's namespace. |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: only skb_tx_error() a packet we are about to drop
queue_userspace_packet() borrows the packet skb -- it only copies it into
a private netlink message (user_skb) and does not own it; on return
do_execute_actions() keeps forwarding it through the flow's remaining
actions. Its error path nevertheless calls skb_tx_error(skb), which via
skb_zcopy_clear() does skb_shinfo(skb)->flags &= ~SKBFL_ALL_ZEROCOPY,
stripping SKBFL_SHARED_FRAG from that live skb (skb_tx_error()'s kerneldoc
says "skb must be freed afterwards").
For a MSG_ZEROCOPY skb carrying page-cache frags, SKBFL_SHARED_FRAG is
what makes esp_input() skb_cow_data() before in-place AEAD; once it is
stripped a later local ESP-in-UDP delivery decrypts in place over pages
the sender does not own -- an unprivileged page-cache write (the
"Fragnesia" primitive).
do_execute_actions() ignores output_userspace()'s return value, so any
action after a failed USERSPACE upcall inherits the stripped skb.
Move the skb_tx_error() to the flow-miss drop path - the "default"
branch of ovs_dp_process_packet()'s switch(error), before kfree_skb().
The call has been here since commit 36d5fe6a0007 ("core, nfqueue,
openvswitch: Orphan frags in skb_zerocopy and handle errors") but was
harmless until esp_input() began relying on SKBFL_SHARED_FRAG to gate
in-place decrypt; only then did stripping it on a still-forwarded skb
become a page-cache write primitive. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: zero the discard fallback page
nvme_setup_discard() always maps sizeof(struct nvme_dsm_range) *
NVME_DSM_MAX_RANGES = 4096 bytes as the DSM payload however many ranges
the command declares, because some devices ignore the 'Number of Ranges'
field - the Fixes: commit records two that read past the declared ranges.
A single-range discard fills only the first 16 bytes.
Normally the buffer comes from kzalloc() and the other 4080 bytes are
zero. When that allocation fails the code falls back to the
per-controller ctrl->discard_page, which nvme_init_ctrl() obtains with
alloc_page(GFP_KERNEL) and nothing ever zeroes, so those 4080 bytes are
whatever the page last held and are handed to the controller. Reaching
it requires the kzalloc(GFP_ATOMIC | __GFP_NOWARN) to fail, that is
memory pressure; it is not remotely triggerable. Failing the allocation
under KMSAN reproduces it, with the leaked tail full of vmemmap struct
page pointers. The extent in the report is a partial transfer of the
payload, not the whole 4096 bytes; the 16-byte boundary in it is the one
declared range:
[ 11.991601] BUG: KMSAN: uninit-value in dma_map_phys+0x14c8/0x1900
[ 11.991969] dma_map_phys+0x14c8/0x1900
[ 11.992220] dma_map_page_attrs+0xcf/0x130
[ 11.992485] e1000_xmit_frame+0x4099/0x6d10
[ 11.992768] dev_hard_start_xmit+0x22f/0xa80
[ 11.993068] sch_direct_xmit+0x35c/0xcb0
[ 11.993315] __dev_queue_xmit+0x1ee5/0x5eb0
[ 11.993608] ip_finish_output2+0x1903/0x1c30
[ 11.993881] ip_finish_output+0x288/0x870
[ 11.994125] ip_output+0x15e/0x400
[ 11.994365] __ip_queue_xmit+0x1e85/0x1fb0
[ 11.994639] ip_queue_xmit+0x60/0x80
[ 11.994899] __tcp_transmit_skb+0x4e71/0x5fa0
[ 11.995210] tcp_write_xmit+0x3a36/0x9160
[ 11.995533] __tcp_push_pending_frames+0xc5/0x3c0
[ 11.995854] tcp_push+0x7dc/0x840
[ 11.996076] tcp_sendmsg_locked+0x766c/0x8400
[ 11.996371] tcp_sendmsg+0x4b/0x90
[ 11.996572] inet_sendmsg+0x134/0x2a0
[ 11.996823] __sock_sendmsg+0x265/0x360
[ 11.997076] sock_sendmsg+0x100/0x1e0
[ 11.997293] nvme_tcp_try_send+0x196f/0x6370
[ 11.997605] nvme_tcp_queue_rq+0x1d54/0x20b0
[ 11.997882] blk_mq_dispatch_rq_list+0x5ee/0x2e50
[ 11.998175] __blk_mq_sched_dispatch_requests+0x16dc/0x24a0
[ 11.998539] blk_mq_sched_dispatch_requests+0x11b/0x2c0
[ 11.998865] blk_mq_run_work_fn+0x13b/0x280
[ 11.999146] process_scheduled_works+0x966/0x1ad0
[ 11.999465] worker_thread+0xe44/0x1480
[ 11.999709] kthread+0x53b/0x600
[ 11.999927] ret_from_fork+0x29f/0x7c0
[ 12.000191] ret_from_fork_asm+0x1a/0x30
[ 12.000460]
[ 12.000558] Uninit was created at:
[ 12.000788] __alloc_frozen_pages_noprof+0x8bf/0xd30
[ 12.001096] alloc_pages_mpol+0x1d0/0x5f0
[ 12.001326] alloc_pages_noprof+0x102/0x290
[ 12.001627] nvme_init_ctrl+0x5a3/0x9f0
[ 12.001891] nvme_tcp_create_ctrl+0xd75/0x19b0
[ 12.002170] nvmf_dev_write+0x4c68/0x4fd0
[ 12.002426] vfs_write+0x587/0x1a10
[ 12.002636] __x64_sys_write+0x207/0x4f0
[ 12.002874] x64_sys_call+0x2ff0/0x3ea0
[ 12.003123] do_syscall_64+0x147/0x3b0
[ 12.003400] entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 12.003680]
[ 12.003777] Bytes 16-2843 of 2844 are uninitialized
[ 12.004068] Memory access of size 2844 starts at ffff888109f82000
[ 12.004412]
[ 12.004530] CPU: 0 UID: 0 PID: 101 Comm: kworker/0:1H Not tainted 7.2.0-rc5-NVMECTL-gf5098b6bae76 #1 PREEMPT(lazy)
[ 12.005127] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 12.005762] Workqueue: kblockd blk_mq_run_work_fn
[ 12.006073] =====================================================
Allocate the page with __GFP_ZERO. The single allocation site covers
every use of it: bytes no discard has written stay zero, and bytes one
did write hold that controller's own range list, which it has already
been sent. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-tcp: do not accept C2HData based on blk_rq_payload_bytes() alone
Commit 25e5cb780e62 ("nvme-tcp: fix possible crash in write_zeroes
processing") established that blk_rq_payload_bytes() must not be read
without first checking blk_rq_nr_phys_segments(), and recorded the
result in nvme_tcp_setup_cmd_pdu() as req->data_len. The receive side
was left as it was.
The two differ for REQ_OP_WRITE_ZEROES, which has no physical segments
but a non-zero blk_rq_bytes(), so setup leaves req->iter untouched
while the receive gate lets a C2HData through and nvme_tcp_recv_data()
copies into whatever the previous command on that tag left there. The
driver-private area is zeroed only when the tag set is allocated.
Reproduced with a test target that leaves a residual iterator on a tag
and then sends a C2HData for a WRITE_ZEROES command on the same tag:
BUG: KASAN: wild-memory-access in _copy_to_iter+0x642/0x1330
Write of size 512 at addr ffe728c2175dfa81 by task kworker/0:1H/103
CPU: 0 UID: 0 PID: 103 Comm: kworker/0:1H Not tainted 7.2.0-rc5-NVMETCP-gf5098b6bae76 #1 PREEMPT(lazy)
Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: nvme_tcp_wq nvme_tcp_io_work
Call Trace:
<TASK>
dump_stack_lvl+0x53/0x70
kasan_report+0xce/0x100
? _copy_to_iter+0x642/0x1330
kasan_check_range+0x105/0x1b0
__asan_memcpy+0x3c/0x60
_copy_to_iter+0x642/0x1330
? __pfx_sock_has_perm+0x10/0x10
? worker_thread+0x45b/0xd10
? __pfx__copy_to_iter+0x10/0x10
? _raw_spin_lock_bh+0x83/0xe0
? __pfx__raw_spin_lock_bh+0x10/0x10
__skb_datagram_iter+0xf3/0x820
? __pfx_simple_copy_to_iter+0x10/0x10
? __asan_memcpy+0x3c/0x60
? skb_copy_bits+0x58d/0x830
skb_copy_datagram_iter+0x37/0x120
nvme_tcp_recv_skb+0xa07/0x4320
? __pfx_nvme_tcp_recv_skb+0x10/0x10
__tcp_read_sock+0x1ab/0x810
? __pfx_nvme_tcp_recv_skb+0x10/0x10
? __pfx_lock_sock_nested+0x10/0x10
? __pfx___tcp_read_sock+0x10/0x10
nvme_tcp_try_recv+0x152/0x1e0
? __pfx_nvme_tcp_try_recv+0x10/0x10
? __pfx_mutex_unlock+0x10/0x10
nvme_tcp_io_work+0x1e4/0x6c0
? __schedule+0x181a/0x49f0
? __pfx_nvme_tcp_io_work+0x10/0x10
process_one_work+0x633/0x1030
Keep the blk_rq_payload_bytes() test and add req->data_len to it. The
old test is what rejects a C2HData naming a tag that is no longer in
flight, because blk_update_request() zeroes rq->__data_len on
completion; req->data_len and req->curr_bio are driver-private and
survive completion, so they cannot stand in for it. Setup initialises
the iterator only when both req->curr_bio and req->data_len are set, so
the gate now tests the same two. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-tcp: fix host memory disclosure on R2T for a read command
nvme_tcp_handle_r2t() does not check the direction of the request the
R2T refers to. A malicious controller can send an R2T for a READ and
the host will answer it: nvme_tcp_setup_h2c_data_pdu() builds the
H2CData header and nvme_tcp_try_send_data() sends the request's data
buffer. That buffer is the READ destination, so its contents go to the
controller.
The command then completes normally and nothing is logged.
Against a test controller that answers every READ with an R2T, a 4096
byte buffered read returned all 4096 bytes, split over two R2Ts. The
pages contained stale kernel data, including an array of struct page
pointers.
Reject an R2T for a request that is not a write. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-tcp: reject a read that transferred too few bytes
nvme_tcp_recv_data() completes a request once the current C2HData PDU
has been consumed. Nothing compares the total bytes received against
the length the command asked for: struct nvme_tcp_request has no
receive-side counter, queue->data_remaining is per queue, and
blk_mq_end_request() completes for blk_rq_bytes(rq) unconditionally
with no residual concept anywhere above.
A controller can therefore answer a 4096-byte read with 512 bytes and
have it reported as a complete read; user space then gets 4096 bytes of
which 3584 are whatever was already in the page. I reproduced that with
a test target.
Count the bytes received and refuse to complete a successful read whose
count does not match, at the two NVME_TCP_F_DATA_SUCCESS paths and in
nvme_tcp_process_nvme_cqe(). The success test shifts req->status right
by one, because the driver keeps the wire value there and shifts it on
completion, so the check must see what the completion path will see.
Only REQ_OP_READ is checked, because there the length comes from the
sectors the request covers; a passthrough command is built by its
submitter, which picks both command and buffer, so the kernel has
nothing to compare against. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: stop processing a packet once its association is deleted
sctp_endpoint_bh_rcv() looks the association up only when chunk->asoc is
NULL, and caches the result in chunk->asoc and chunk->transport without
taking a reference.
A packet that matches no association is handed to the endpoint, so a peer
can bundle COOKIE ECHO, SHUTDOWN and SHUTDOWN ACK in one packet. The
COOKIE ECHO creates the association, the SHUTDOWN chunk caches it, and
with the outqueue empty the SHUTDOWN ACK reaches sctp_sf_do_9_2_final(),
so the association and its transports are freed.
The endpoint loop has no counterpart to the asoc->base.dead check in
sctp_assoc_bh_rcv(). The next chunk writes to last_time_heard in the freed
transport and is then passed to sctp_do_sm() with the freed association.
The transport is freed through RCU, so this needs the packet to come off
the socket backlog, where the loop runs in task context.
The endpoint loop cannot do the same check: it holds no reference on the
association, so reading asoc->base.dead would itself be a use-after-free.
Mark the packet for discard in the command interpreter, just before it
deletes the association. That is also before sctp_inq_free() releases the
chunk on the association receive path.
sctp_sf_do_5_2_4_dupcook() issues SCTP_CMD_DELETE_TCB for the temporary
association, while the one the packet belongs to stays alive. A restarting
peer can bundle DATA behind its COOKIE ECHO, so compare against
chunk->asoc and leave that case alone. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: drop a chunk if its transport was removed
sctp_rcv() resolves the transport once per packet and leaves it in
chunk->transport. The lookup reference, or the one sctp_add_backlog() takes
if the socket is owned by userspace, keeps it around until the chunk has
been processed.
An authenticated ASCONF DEL-IP can remove it in the meantime.
sctp_assoc_rm_peer() takes the transport out of the association and calls
sctp_transport_free(), which tags it dead and drops the reference the
association held. There is a window on both paths: the packet can sit on
the socket backlog, and on the direct path the lookup completes before
bh_lock_sock().
The DATA chunk in that packet puts the removed transport back into
asoc->peer.last_data_from. Once the packet is done that reference goes
away and the transport is freed by RCU, so the next delayed SACK carries
the pointer into the SACK chunk and sctp_outq_select_transport() reads the
freed transport's state.
Drop the chunk in sctp_inq_push(), next to the existing rcvr->dead check.
Both paths reach it with the association's socket lock held. The peer
retransmits it. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix NULL deref on untransmitted RECONF completion
sctp_process_strreset_outreq(), sctp_process_strreset_addstrm_out() and
sctp_process_strreset_resp() complete a pending stream reconfiguration
request by stopping the reconf timer on the transport it was sent on:
t = asoc->strreset_chunk->transport;
if (timer_delete(&t->reconf_timer))
sctp_transport_put(t);
chunk->transport is assigned by __sctp_packet_append_chunk() when the
chunk is appended to an outbound packet, and sctp_outq_flush_ctrl() arms
the reconf timer at that same point. A request already published in
asoc->strreset_chunk but not yet transmitted has neither, so completing
it dereferences NULL.
Two ways to get there. sctp_send_asconf_del_ip() sets
asoc->src_out_of_asoc_ok without sending anything when the address being
removed is the association's last one, and sctp_outq_flush_ctrl() then
leaves every non-ASCONF control chunk queued; as only
sctp_process_asconf_ack() clears that flag, it persists. An unprivileged
process that removes such an address and then asks for a stream reset
panics the kernel from softirq. A peer needs neither ASCONF nor local
help: sctp_cmd_interpreter() uncorks the outqueue only once the whole
packet has been processed, so a reply built while walking a RECONF chunk
stays untransmitted for the rest of that walk, and one RECONF chunk
carrying [Incoming SSN Reset Request, Outgoing SSN Reset Request,
Response] -- or two RECONF chunks in one packet -- reaches the same
dereference.
KASAN: null-ptr-deref in range [0x00000000000001e8-0x00000000000001ef]
RIP: 0010:timer_delete+0x67/0x110
Call Trace:
<IRQ>
sctp_process_strreset_addstrm_out (net/sctp/stream.c:832)
sctp_sf_do_reconf (net/sctp/sm_statefuns.c:4212)
sctp_do_sm (net/sctp/sm_sideeffect.c:1172)
sctp_assoc_bh_rcv (net/sctp/associola.c:1044)
sctp_rcv (net/sctp/input.c:243)
ip_local_deliver (net/ipv4/ip_input.c:262)
process_backlog (net/core/dev.c:6680)
</IRQ>
A response can only acknowledge a request that was actually sent, so do
not match asoc->strreset_chunk while chunk->transport is NULL. Guarding
the lookup covers all three completion sites. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix stream->outcnt underflow on duplicate RECONF responses
A cached RECONF chunk may contain more than one request parameter. A
duplicate response can therefore find and process the same ADD_OUT request
again while another parameter is still outstanding, rolling back outcnt
twice and possibly underflowing it.
Track outstanding request types as bits and clear each bit after its first
response. Later responses for the same request are then ignored. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Force requesting ACS when tboot is enabled
Currently the conditions of requesting ACS in detect_intel_iommu()
don't include tboot, leading to a possible misconfiguration with ACS
disabled (e.g. due to user opts) while iommu is later forced on by
tboot_force_iommu().
Fix it by checking tboot in detect_intel_iommu(). |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: via-sdmmc: cancel card-detect work on remove
Disabling the device interrupt and freeing the IRQ prevents new card-detect
work from being queued, but carddet_work already queued by the handler can
still run after via_sd_remove() returns. via_sdc_card_detect() recovers the
host through container_of() and dereferences its MMIO base; once remove()
returns the host can be freed, so that work would touch freed memory.
Cancel carddet_work after freeing the IRQ and before cancelling
finish_bh_work, which the card-detect handler can also queue. carddet_work
can re-enable the interrupt through via_reset_pcictrl(); mask it again
afterwards.
This issue was found by an in-house static analysis tool and confirmed by
manual code review. |
| undici is an HTTP client library for Node.js. In versions 7.15.0 through 7.30.0 and 8.0.0 through 8.12.1, its decompress interceptor forwards decompressed response data to the downstream handler from zlib stream event callbacks without catching exceptions those callbacks may throw, and while undici's engine converts a synchronous throw from a downstream handler into a per-request failure, that protection is absent when the throw happens asynchronously from a zlib callback. As a result, a downstream handler that throws by design, such as the built-in dump interceptor which throws when a response exceeds its configured maximum size, escapes as an uncaught exception that terminates the Node.js process. A malicious or compromised HTTP server can crash any client that composes the decompress interceptor with such a handler by returning a small compressed body that decompresses to more than the configured limit, so only the decompressed size matters and the bytes on the wire stay tiny. The issue is fixed in undici 7.30.1 and 8.12.2, and users should upgrade to one of those versions or later. As a workaround, avoid composing the decompress interceptor with a response handler that throws during response processing until upgrading. |
| undici is an HTTP client library for Node.js. In versions 4.2.1 through 6.29.0, 7.0.0 through 7.30.0, and 8.0.0 through 8.12.1, the client process crashes when a TLS 1.2 server renegotiates after the connection is established and presents a different, CA-trusted certificate whose hostname does not match the requested host. Node.js re-runs hostname verification on the renegotiated handshake and destroys the socket with a certificate-altname error, but undici's established-socket error handler asserted that this error code could never occur, so the peer-controlled error became an uncaught assertion that terminates the Node.js process, affecting both the HTTP/1.1 and HTTP/2 paths. A malicious or compromised HTTPS endpoint reached through undici or the global fetch() can crash the client with a single server-initiated renegotiation, taking down all in-flight requests and background work in the process, and exploitation needs no CA compromise because the attacker controls the endpoint and can present two ordinary valid certificates. Only TLS 1.2 is affected, since TLS 1.3 does not support renegotiation. The issue is fixed in undici 6.29.1, 7.30.1, and 8.12.2, and users should upgrade to one of those versions or later. As a workaround, restrict outbound connections to TLS 1.3 so renegotiation cannot occur, when the target endpoints support it. |
