| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
inotify: fix watch count leak when fsnotify_add_inode_mark_locked() fails
When fsnotify_add_inode_mark_locked() fails in inotify_new_watch(),
the error path calls inotify_remove_from_idr() but does not call
dec_inotify_watches() to undo the preceding inc_inotify_watches().
This leaks a watch count, and repeated failures can exhaust the
max_user_watches limit with -ENOSPC even when no watches are active.
Prior to commit 1cce1eea0aff ("inotify: Convert to using per-namespace
limits"), the watch count was incremented after fsnotify_add_mark_locked()
succeeded, so this path was not affected. The conversion moved
inc_inotify_watches() before the mark insertion without adding the
corresponding rollback.
Add the missing dec_inotify_watches() call in the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: ns: Free the node during ctrl_cmd_bye()
A node sends the BYE packet when it is about to go down. So the nameserver
should advertise the removal of the node to all remote and local observers
and free the node finally. But currently, the nameserver doesn't free the
node memory even after processing the BYE packet. This causes the node
memory to leak.
Hence, remove the node from Xarray list and free the node memory during
both success and failure case of ctrl_cmd_bye(). |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: icmp: validate reply type before using icmp_pointers
Extended echo replies use ICMP_EXT_ECHOREPLY as the outbound reply type.
That value is outside the range covered by icmp_pointers[], which only
describes the traditional ICMP types up to NR_ICMP_TYPES.
Avoid consulting icmp_pointers[] for reply types outside that range, and
use array_index_nospec() for the remaining in-range lookup. Normal ICMP
replies keep their existing behavior unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: authencesn - reject short ahash digests during instance creation
authencesn requires either a zero authsize or an authsize of at least
4 bytes because the ESN encrypt/decrypt paths always move 4 bytes of
high-order sequence number data at the end of the authenticated data.
While crypto_authenc_esn_setauthsize() already rejects explicit
non-zero authsizes in the range 1..3, crypto_authenc_esn_create()
still copied auth->digestsize into inst->alg.maxauthsize without
validating it. The AEAD core then initialized the tfm's default
authsize from that value.
As a result, selecting an ahash with digest size 1..3, such as
cbcmac(cipher_null), exposed authencesn instances whose default
authsize was invalid even though setauthsize() would have rejected the
same value. AF_ALG could then trigger the ESN tail handling with a
too-short tag and hit an out-of-bounds access.
Reject authencesn instances whose ahash digest size is in the invalid
non-zero range 1..3 so that no tfm can inherit an unsupported default
authsize. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: ns: Limit the maximum number of lookups
Current code does no bound checking on the number of lookups a client can
perform. Though the code restricts the lookups to local clients, there is
still a possibility of a malicious local client sending a flood of
NEW_LOOKUP messages over the same socket.
Fix this issue by limiting the maximum number of lookups to 64 globally.
Since the nameserver allows only atmost one local observer, this global
lookup count will ensure that the lookups stay within the limit.
Note that, limit of 64 is chosen based on the current platform
requirements. If requirement changes in the future, this limit can be
increased. |
| In the Linux kernel, the following vulnerability has been resolved:
dm mirror: fix integer overflow in create_dirty_log()
The argument count calculation in create_dirty_log() performs
`*args_used = 2 + param_count` before validating against argc. When a
user provides a param_count close to UINT_MAX via the device mapper
table string, this unsigned addition wraps around to a small value,
causing the subsequent `argc < *args_used` check to be bypassed.
The overflowed param_count is then passed as argc to dm_dirty_log_create(),
where it can cause out-of-bounds reads on the argv array.
Fix by comparing param_count against argc - 2 before performing the
addition, following the same pattern used by parse_features() in the
same file. Since argc >= 2 is already guaranteed, the subtraction is
safe. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: ibmasm: fix OOB MMIO read in ibmasm_handle_mouse_interrupt()
ibmasm_handle_mouse_interrupt() performs an out-of-bounds MMIO read
when the queue reader or writer index from hardware exceeds
REMOTE_QUEUE_SIZE (60).
A compromised service processor can trigger this by writing an
out-of-range value to the reader or writer MMIO register before
asserting an interrupt. Since writer is re-read from hardware on
every loop iteration, it can also be set to an out-of-range value
after the loop has already started.
The root cause is that get_queue_reader() and get_queue_writer() return
raw readl() values that are passed directly into get_queue_entry(),
which computes:
queue_begin + reader * sizeof(struct remote_input)
with no bounds check. This unchecked MMIO address is then passed to
memcpy_fromio(), reading 8 bytes from unintended device registers.
For sufficiently large values the address falls outside the PCI BAR
mapping entirely, triggering a machine check exception.
Fix by checking both indices against REMOTE_QUEUE_SIZE at the top of
the loop body, before any call to get_queue_entry(). On an out-of-range
value, reset the reader register to 0 via set_queue_reader() before
breaking, so that normal queue operation can resume if the corrupted
hardware state is transient. |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: core: Fix thermal zone governor cleanup issues
If thermal_zone_device_register_with_trips() fails after adding
a thermal governor to the thermal zone being registered, the
governor is not removed from it as appropriate which may lead to
a memory leak.
In turn, thermal_zone_device_unregister() calls thermal_set_governor()
without acquiring the thermal zone lock beforehand which may race with
a governor update via sysfs and may lead to a use-after-free in that
case.
Address these issues by adding two thermal_set_governor() calls, one to
thermal_release() to remove the governor from the given thermal zone,
and one to the thermal zone registration error path to cover failures
preceding the thermal zone device registration. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: stop parsing UAC2 rates at MAX_NR_RATES
parse_uac2_sample_rate_range() caps the number of enumerated
rates at MAX_NR_RATES, but it only breaks out of the current
rate loop. A malformed UAC2 RANGE response with additional
triplets continues parsing the remaining triplets and repeatedly
prints "invalid uac2 rates" while probe still holds
register_mutex.
Stop the whole parse once the cap is reached and return the
number of rates collected so far. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: call sk_data_ready() after listener migration
When inet_csk_listen_stop() migrates an established child socket from
a closing listener to another socket in the same SO_REUSEPORT group,
the target listener gets a new accept-queue entry via
inet_csk_reqsk_queue_add(), but that path never notifies the target
listener's waiters. A nonblocking accept() still works because it
checks the queue directly, but poll()/epoll_wait() waiters and
blocking accept() callers can also remain asleep indefinitely.
Call READ_ONCE(nsk->sk_data_ready)(nsk) after a successful migration
in inet_csk_listen_stop().
However, after inet_csk_reqsk_queue_add() succeeds, the ref acquired
in reuseport_migrate_sock() is effectively transferred to
nreq->rsk_listener. Another CPU can then dequeue nreq via accept()
or listener shutdown, hit reqsk_put(), and drop that listener ref.
Since listeners are SOCK_RCU_FREE, wrap the post-queue_add()
dereferences of nsk in rcu_read_lock()/rcu_read_unlock(), which also
covers the existing sock_net(nsk) access in that path.
The reqsk_timer_handler() path does not need the same changes for two
reasons: half-open requests become readable only after the final ACK,
where tcp_child_process() already wakes the listener; and once nreq is
visible via inet_ehash_insert(), the success path no longer touches
nsk directly. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: ns: Limit the total number of nodes
Currently, the nameserver doesn't limit the number of nodes it handles.
This can be an attack vector if a malicious client starts registering
random nodes, leading to memory exhaustion.
Hence, limit the maximum number of nodes to 64. Note that, limit of 64 is
chosen based on the current platform requirements. If requirement changes
in the future, this limit can be increased. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: sd: fix missing put_disk() when device_add(&disk_dev) fails
If device_add(&sdkp->disk_dev) fails, put_device() runs
scsi_disk_release(), which frees the scsi_disk but leaves the gendisk
referenced. The device_add_disk() error path in sd_probe() calls
put_disk(gd); call put_disk(gd) here to mirror that cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
udf: fix partition descriptor append bookkeeping
Mounting a crafted UDF image with repeated partition descriptors can
trigger a heap out-of-bounds write in part_descs_loc[].
handle_partition_descriptor() deduplicates entries by partition number,
but appended slots never record partnum. As a result duplicate
Partition Descriptors are appended repeatedly and num_part_descs keeps
growing.
Once the table is full, the growth path still sizes the allocation from
partnum even though inserts are indexed by num_part_descs. If partnum is
already aligned to PART_DESC_ALLOC_STEP, ALIGN(partnum, step) can keep
the old capacity and the next append writes past the end of the table.
Store partnum in the appended slot and size growth from the next append
count so deduplication and capacity tracking follow the same model. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: skip ipv6 extension headers for csum checks
Protocol checksum validation fails for IPv6 if there are extension
headers before the protocol header. iph->len already contains its
offset, so use it to fix the problem. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: arp_tables: fix IEEE1394 ARP payload parsing
Weiming Shi says:
"arp_packet_match() unconditionally parses the ARP payload assuming two
hardware addresses are present (source and target). However,
IPv4-over-IEEE1394 ARP (RFC 2734) omits the target hardware address
field, and arp_hdr_len() already accounts for this by returning a
shorter length for ARPHRD_IEEE1394 devices.
As a result, on IEEE1394 interfaces arp_packet_match() advances past a
nonexistent target hardware address and reads the wrong bytes for both
the target device address comparison and the target IP address. This
causes arptables rules to match against garbage data, leading to
incorrect filtering decisions: packets that should be accepted may be
dropped and vice versa.
The ARP stack in net/ipv4/arp.c (arp_create and arp_process) already
handles this correctly by skipping the target hardware address for
ARPHRD_IEEE1394. Apply the same pattern to arp_packet_match()."
Mangle the original patch to always return 0 (no match) in case user
matches on the target hardware address which is never present in
IEEE1394.
Note that this returns 0 (no match) for either normal and inverse match
because matching in the target hardware address in ARPHRD_IEEE1394 has
never been supported by arptables. This is intentional, matching on the
target hardware address should never evaluate true for ARPHRD_IEEE1394.
Moreover, adjust arpt_mangle to drop the packet too as AI suggests:
In arpt_mangle, the logic assumes a standard ARP layout. Because
IEEE1394 (FireWire) omits the target hardware address, the linear
pointer arithmetic miscalculates the offset for the target IP address.
This causes mangling operations to write to the wrong location, leading
to packet corruption. To ensure safety, this patch drops packets
(NF_DROP) when mangling is requested for these fields on IEEE1394
devices, as the current implementation cannot correctly map the FireWire
ARP payload.
This omits both mangling target hardware and IP address. Even if IP
address mangling should be possible in IEEE1394, this would require
to adjust arpt_mangle offset calculation, which has never been
supported.
Based on patch from Weiming Shi <bestswngs@gmail.com>. |
| In the Linux kernel, the following vulnerability has been resolved:
slip: bound decode() reads against the compressed packet length
slhc_uncompress() parses a VJ-compressed TCP header by advancing a
pointer through the packet via decode() and pull16(). Neither helper
bounds-checks against isize, and decode() masks its return with
& 0xffff so it can never return the -1 that callers test for -- those
error paths are dead code.
A short compressed frame whose change byte requests optional fields
lets decode() read past the end of the packet. The over-read bytes
are folded into the cached cstate and reflected into subsequent
reconstructed packets.
Make decode() and pull16() take the packet end pointer and return -1
when exhausted. Add a bounds check before the TCP-checksum read.
The existing == -1 tests now do what they were always meant to. |
| In the Linux kernel, the following vulnerability has been resolved:
slip: reject VJ receive packets on instances with no rstate array
slhc_init() accepts rslots == 0 as a valid configuration, with the
documented meaning of 'no receive compression'. In that case the
allocation loop in slhc_init() is skipped, so comp->rstate stays
NULL and comp->rslot_limit stays 0 (from the kzalloc of struct
slcompress).
The receive helpers do not defend against that configuration.
slhc_uncompress() dereferences comp->rstate[x] when the VJ header
carries an explicit connection ID, and slhc_remember() later assigns
cs = &comp->rstate[...] after only comparing the packet's slot number
to comp->rslot_limit. Because rslot_limit is 0, slot 0 passes the
range check, and the code dereferences a NULL rstate.
The configuration is reachable in-tree through PPP. PPPIOCSMAXCID
stores its argument in a signed int, and (val >> 16) uses arithmetic
shift. Passing 0xffff0000 therefore sign-extends to -1, so val2 + 1
is 0 and ppp_generic.c ends up calling slhc_init(0, 1). Because
/dev/ppp open is gated by ns_capable(CAP_NET_ADMIN), the whole path
is reachable from an unprivileged user namespace. Once the malformed
VJ state is installed, any inbound VJ-compressed or VJ-uncompressed
frame that selects slot 0 crashes the kernel in softirq context:
Oops: general protection fault, probably for non-canonical
address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:slhc_uncompress (drivers/net/slip/slhc.c:519)
Call Trace:
<TASK>
ppp_receive_nonmp_frame (drivers/net/ppp/ppp_generic.c:2466)
ppp_input (drivers/net/ppp/ppp_generic.c:2359)
ppp_async_process (drivers/net/ppp/ppp_async.c:492)
tasklet_action_common (kernel/softirq.c:926)
handle_softirqs (kernel/softirq.c:623)
run_ksoftirqd (kernel/softirq.c:1055)
smpboot_thread_fn (kernel/smpboot.c:160)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:164)
</TASK>
Reject the receive side on such instances instead of touching rstate.
slhc_uncompress() falls through to its existing 'bad' label, which
bumps sls_i_error and enters the toss state. slhc_remember() mirrors
that with an explicit sls_i_error increment followed by slhc_toss();
the sls_i_runt counter is not used here because a missing rstate is
an internal configuration state, not a runt packet.
The transmit path is unaffected: the only in-tree caller that picks
rslots from userspace (ppp_generic.c) still supplies tslots >= 1, and
slip.c always calls slhc_init(16, 16), so comp->tstate remains valid
and slhc_compress() continues to work. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_osf: fix divide-by-zero in OSF_WSS_MODULO
nf_osf_match_one() computes ctx->window % f->wss.val in the
OSF_WSS_MODULO branch with no guard for f->wss.val == 0. A
CAP_NET_ADMIN user can add such a fingerprint via nfnetlink; a
subsequent matching TCP SYN divides by zero and panics the kernel.
Reject the bogus fingerprint in nfnl_osf_add_callback() above the
per-option for-loop. f->wss is per-fingerprint, not per-option, so
the check must run regardless of f->opt_num (including 0). Also
reject wss.wc >= OSF_WSS_MAX; nf_osf_match_one() already treats that
as "should not happen".
Crash:
Oops: divide error: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:nf_osf_match_one (net/netfilter/nfnetlink_osf.c:98)
Call Trace:
<IRQ>
nf_osf_match (net/netfilter/nfnetlink_osf.c:220)
xt_osf_match_packet (net/netfilter/xt_osf.c:32)
ipt_do_table (net/ipv4/netfilter/ip_tables.c:348)
nf_hook_slow (net/netfilter/core.c:622)
ip_local_deliver (net/ipv4/ip_input.c:265)
ip_rcv (include/linux/skbuff.h:1162)
__netif_receive_skb_one_core (net/core/dev.c:6181)
process_backlog (net/core/dev.c:6642)
__napi_poll (net/core/dev.c:7710)
net_rx_action (net/core/dev.c:7945)
handle_softirqs (kernel/softirq.c:622) |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: cap upcall PID array size and pre-size vport replies
The vport netlink reply helpers allocate a fixed-size skb with
nlmsg_new(NLMSG_DEFAULT_SIZE, ...) but serialize the full upcall PID
array via ovs_vport_get_upcall_portids(). Since
ovs_vport_set_upcall_portids() accepts any non-zero multiple of
sizeof(u32) with no upper bound, a CAP_NET_ADMIN user can install a PID
array large enough to overflow the reply buffer, causing nla_put() to
fail with -EMSGSIZE and hitting BUG_ON(err < 0). On systems with
unprivileged user namespaces enabled (e.g., Ubuntu default), this is
reachable via unshare -Urn since OVS vport mutation operations use
GENL_UNS_ADMIN_PERM.
kernel BUG at net/openvswitch/datapath.c:2414!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 1 UID: 0 PID: 65 Comm: poc Not tainted 7.0.0-rc7-00195-geb216e422044 #1
RIP: 0010:ovs_vport_cmd_set+0x34c/0x400
Call Trace:
<TASK>
genl_family_rcv_msg_doit (net/netlink/genetlink.c:1116)
genl_rcv_msg (net/netlink/genetlink.c:1194)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
genl_rcv (net/netlink/genetlink.c:1219)
netlink_unicast (net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sys_sendto (net/socket.c:2206)
__x64_sys_sendto (net/socket.c:2209)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
Kernel panic - not syncing: Fatal exception
Reject attempts to set more PIDs than nr_cpu_ids in
ovs_vport_set_upcall_portids(), and pre-compute the worst-case reply
size in ovs_vport_cmd_msg_size() based on that bound, similar to the
existing ovs_dp_cmd_msg_size(). nr_cpu_ids matches the cap already
used by the per-CPU dispatch configuration on the datapath side
(ovs_dp_cmd_fill_info() serialises at most nr_cpu_ids PIDs), so the
two sides stay consistent. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: reject negative CO-RE accessor indices in bpf_core_parse_spec()
CO-RE accessor strings are colon-separated indices that describe a path
from a root BTF type to a target field, e.g. "0:1:2" walks through
nested struct members. bpf_core_parse_spec() parses each component with
sscanf("%d"), so negative values like -1 are silently accepted. The
subsequent bounds checks (access_idx >= btf_vlen(t)) only guard the
upper bound and always pass for negative values because C integer
promotion converts the __u16 btf_vlen result to int, making the
comparison (int)(-1) >= (int)(N) false for any positive N.
When -1 reaches btf_member_bit_offset() it gets cast to u32 0xffffffff,
producing an out-of-bounds read far past the members array. A crafted
BPF program with a negative CO-RE accessor on any struct that exists in
vmlinux BTF (e.g. task_struct) crashes the kernel deterministically
during BPF_PROG_LOAD on any system with CONFIG_DEBUG_INFO_BTF=y
(default on major distributions). The bug is reachable with CAP_BPF:
BUG: unable to handle page fault for address: ffffed11818b6626
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 85 Comm: poc Not tainted 7.0.0-rc6 #18 PREEMPT(full)
RIP: 0010:bpf_core_parse_spec (tools/lib/bpf/relo_core.c:354)
RAX: 00000000ffffffff
Call Trace:
<TASK>
bpf_core_calc_relo_insn (tools/lib/bpf/relo_core.c:1321)
bpf_core_apply (kernel/bpf/btf.c:9507)
check_core_relo (kernel/bpf/verifier.c:19475)
bpf_check (kernel/bpf/verifier.c:26031)
bpf_prog_load (kernel/bpf/syscall.c:3089)
__sys_bpf (kernel/bpf/syscall.c:6228)
</TASK>
CO-RE accessor indices are inherently non-negative (struct member index,
array element index, or enumerator index), so reject them immediately
after parsing. |
